Welcome to [Wuxi Chemical Equipment Co., Ltd.] website!

咨询热线:

Heat Exchanger Selection Guide: Types, Configurations and Design Fundamentals

What a Heat Exchanger Does and Why Type Selection Matters

A heat exchanger transfers thermal energy between two fluids that are at different temperatures without mixing them. The hot stream gives up heat, the cold stream absorbs it, and the equipment defines both the duty and the limits of the process. Because the two streams can differ in pressure, phase, cleanliness and chemical composition, no single construction works everywhere. A shell-and-tube unit handles high pressure and dirty service, a plate exchanger handles clean fluids with a small approach temperature, and an air-cooled unit avoids cooling water entirely. Selecting the wrong type is one of the most common causes of undersized equipment, repeated fouling shutdowns and pressure-drop problems that show up months after commissioning. This guide works through the principal configurations, the calculation method used to size them, and the mechanical details that decide how long the unit will stay in service.

Shell-and-Tube Configurations

The shell-and-tube heat exchanger is the reference design for industrial process service. The tube bundle is fixed to a tubesheet, a floating head, or a U-tube bundle, and this choice governs thermal expansion, ease of cleaning and allowable pressure. A fixed tubesheet exchanger is the simplest and most economical design, with the tubesheet welded to the shell and the tube ends expanded or welded into the plate. It suits clean, low-fouling fluids. A U-tube arrangement eliminates the tubesheet entirely; the tubes are bent back into the shell, which gives unlimited expansion freedom, but the U-bend limits the tube length and the flow area in the bend. A floating head allows one end of the bundle to expand freely, with a bolted rather than welded shell-side cover. The removable bundle type allows the entire bundle to be withdrawn for cleaning.

TypeExpansionCleaning accessTypical service
Fixed tubesheetLimitedStraight tube pull onlyClean water, steam
U-tubeUnlimitedStraight pull, bend limits lengthHigh temperature swing
Floating headFree on one endGood, bundle removableGeneral process duty
Removable bundleFree on one endExcellent, full withdrawalCrude, cooling water
Plate and frameFlat gasketed platesExcellent, plates openClean fluids
Spiral plateNot applicableGood, self-cleaningFouling liquids
Air-cooledFree finned bundleCleaning in placeWater unavailable

Plate, Spiral Plate and Frame Constructions

Plate heat exchangers transfer heat through a thin corrugated plate, so the heat transfer coefficient is far higher than in a shell-and-tube unit and the approach temperature can be very small. Corrugation creates turbulence on both sides, and a counter-flow arrangement allows a two-degree approach. Gasketed plate exchangers use compression gaskets between plates, which means the plates can be opened for mechanical cleaning, though the gasket limits design pressure and temperature. Spiral plate exchangers use two rolled plates wound into a cylinder, creating a single long tortuous channel for one fluid and a second channel for the other. This geometry produces high turbulence and self-cleaning behaviour in fouling service and is often used for sludge, digestor liquor and paper-mill effluent. Jacketed vessels and dimple jackets apply a heated or cooled medium to the outside of a process vessel, with the dimple pattern creating turbulence and raising the effective area. Double-pipe heat exchangers use one pipe inside another and remain the simplest option for small duties and condensing steam service.

Heat Transfer Fundamentals and Duty Calculation

All sizing begins with the duty equation Q = U x A x dT, where U is the overall heat transfer coefficient in W/m2K, A is the effective area in m2 and dT is the driving temperature difference. For a single phase fluid the heat capacity rate is expressed as mass flow multiplied by specific heat. When the fluid changes phase, the duty is driven by latent heat, Q = m x r, and the temperature stays nearly constant through the exchanger, which is why condensing and boiling streams are so easy to heat or cool. The log-mean temperature difference is used for counter-flow and parallel-flow arrangements and is corrected by an F factor for real cross-flow or multipass layouts, with F typically between 0.8 and 1.0. Overall heat transfer coefficients are not a constant property of a material. They combine film coefficients on both sides with the wall conductivity and are reduced by a fouling factor representing the thermal resistance of deposited scale. A reasonable starting point for clean water on the tube side and condensing steam on the shell side is a U-value of 1000 to 2000 W/m2K, while dirty process or cooling water service can fall to 200 to 500 W/m2K.

Material Selection and Corrosion Allowance

Materials are chosen from the process chemistry, temperature and pressure rather than from habit. Stainless steel 304 and 316L cover most clean water, steam and general chemical service, with 316L preferred where chlorides, acids or higher temperatures are present. Carbon steel remains economical for oil, steam and neutral aqueous service and is often used on the shell for its mechanical toughness. Copper alloys suit seawater cooling where velocity and corrosion are controlled, and cupronickel is common in marine exchangers. Titanium is the standard answer for hot chloride brines, seawater and pulp bleaching. Hastelloy and other nickel alloys address mixed acid service. Graphite construction resists almost all acids and alkalis and is used in mineral acid duties, while PTFE lining handles media where metal is unsuitable. Corrosion allowance must be added to the wall thickness of shell, tubesheets and tubes, typically 1.5 to 3 mm for carbon steel.

MaterialResistanceCommon application
Carbon steelModerateSteam, oil, neutral water
SS304 / 316LGoodGeneral chemical, treated water
Copper / cupronickelGood in waterSeawater cooling
TitaniumExcellent in chloridesBrine, seawater, pulp bleach
HastelloyExcellent in acidsMixed acid, contaminated streams
GraphiteExcellent in acids and alkalisMineral acid service
PTFE liningExcellent, limited pressureHighly corrosive media

Tube Layout, Pitch and Mechanical Design

The tube arrangement inside a shell determines both performance and constructability. Triangular pitch gives the highest heat transfer area per unit of shell diameter, while square and triangular layouts are the usual practical choices. A pitch that is too small restricts tube-side velocity, increases fouling and makes shell-side mechanical cleaning difficult. A staggered arrangement is generally avoided in dirty service because it traps debris. Tube diameter is a compromise: larger tubes carry more flow with lower velocity and are easier to brush, while smaller tubes give more area in a given shell and raise the pressure drop. Shell nozzles should be placed to achieve a reasonably uniform velocity distribution and to prevent vapour pockets or gas bypassing. Nozzle connections are usually flanged to ASME B16.5 or GB/T 9113 flanges with the rating matched to the design pressure; flanged joints are preferred for field connection and maintenance, while welded nozzle connections are used where leakage risk must be minimised. The shell, tubesheets, channel cover and flanges are designed to ASME Section VIII Division 1, with TEMA 1 giving recommended practice and GB/T 151 providing the Chinese national equivalent. Where the equipment falls under the European Pressure Equipment Directive, conformity assessment applies and the route must be agreed before design begins.

Pressure, Temperature and Testing

Design pressure is set by the highest working pressure at the design temperature, and the design temperature is taken with a margin above the operating temperature. A vacuum service condition must be checked separately, since external pressure governs shell stability and stiffening rings may be required. Heat exchangers are usually treated as pressure vessels, and the design must demonstrate the code minimum wall thickness, allowable stress and, where full nondestructive examination is specified, the corresponding joint efficiency. Hydrostatic testing of the shell and channel is standard, with the tube side and shell side tested separately to the pressures agreed in the purchase specification, and the test pressure is generally 1.3 times the design pressure. The shell leak test detects tube-to-tubesheet or channel leakage, while an eddy current examination of the tubes locates wall thinning and through-wall defects without removing the bundle. For high integrity service, shell-side noise and vibration measurement and a tube-side flow survey are commonly added to the test scope. Following hydrotest, the equipment is flushed, drained and dried to prevent internal corrosion during storage, and the documentation package should include material certificates, weld procedure records, heat treatment records, NDE reports and nameplate data.

Thermal Expansion, Vibration and Support

Thermal expansion is the root cause of many early-life failures. When the shell and tube bundle cannot expand freely, the resulting forces are large and act on the tubesheets, tube-to-tubesheet joints and channel covers. Floating heads, U-tubes and expansion joints address this, and a properly sized expansion joint in a long shell line is often more economical than a full floating head. The differential expansion between shell and tubes creates forces at the tubesheet, which must be carried by the channel, the floating head or an external tie rod arrangement. Vibration is the second major mechanical concern. The main cause of tube failure is fluid-induced vibration from shell-side cross-flow, and the first line of defence is a support plate arrangement that increases tube support stiffness, supplemented by a lower shell-side velocity, a baffle cut appropriate to the flow, and control of acoustic resonance. Antivibration bars and, in severe cases, helical baffles are used where standard segmental baffles are not enough. The equipment must also be checked for piping loads, and nozzles should be reinforced so the vessel wall is not distorted by the connection.

A Practical Selection Sequence

Selection becomes reliable when it is treated as an ordered sequence rather than a jump to a catalogue. First, fix the duty, the stream flow rates, inlet and outlet temperatures, the physical state of each stream and the acceptable pressure drop. Second, identify the corrosive and fouling character of each side, since this drives the material set and the cleaning strategy. Third, calculate the required area from the corrected LMTD and the estimated U-value, including a fouling factor from the start. Fourth, choose the construction: shell-and-tube for high pressure, dirty service or large duties; plate for clean fluids, tight approach and small footprint; air-cooled where water is unavailable; spiral plate for viscous and heavily fouling liquids. Fifth, settle the mechanical details of layout, pitch, baffles, nozzles, flanges and the applicable code, and confirm the insulation, support and expansion philosophy. Finally, define the inspection, testing and maintenance scope, including access for cleaning, tube bundle withdrawal and monitoring points.

Frequently Asked Questions

How is the required heat transfer area calculated?

The area follows from the duty divided by the overall heat transfer coefficient and the corrected log-mean temperature difference, with the fouling factor included in the coefficient. Because the U-value depends on the actual fluid conditions, it is confirmed with data for the specific duty rather than a catalogue default.

Fixed tubesheet or floating head for a hot service?

When the shell and bundle temperatures differ substantially, a floating head or U-tube arrangement is preferred, because it allows differential expansion without overloading the tubesheet and the tube-to-tubesheet joints. A fixed tubesheet remains economical where the temperature swing is modest and the service is clean.

Can a plate heat exchanger handle high pressure?

Plate exchangers with compression gaskets have a limited pressure capability that grows with the plate size, and the gasket material constrains both pressure and temperature. For high pressure or high temperature duty, a welded shell-and-tube unit is normally the correct selection.

What information is needed to start a selection?

Provide the flow rate, inlet and outlet temperature, pressure and phase for both streams, the chemical composition and fouling tendency, the acceptable pressure drop, and the required service life. This defines the duty, the material set and the cleaning philosophy, and it is what a vendor needs to size the equipment.

61 次

相关文档

Copy right © 2019 Wuxi Chemical Equipment Co., Ltd. All Rights Reserved Website Design: Wuxi Wangke