Welcome to [Wuxi Chemical Equipment Co., Ltd.] website!

咨询热线:

Heat Exchanger Operation and Maintenance: Fouling, Efficiency and Troubleshooting

How Heat Exchanger Performance Degrades in Service

A heat exchanger rarely fails suddenly. Its performance normally decays over months or years as deposits build on the heat transfer surfaces, the pressure drop rises, and the corrected temperature difference needed for the duty no longer exists. The first indication is usually a change in the measured outlet temperature for a given flow, or a gradual increase in the differential pressure. Because fouling adds a thermal resistance layer, the effective overall heat transfer coefficient falls. When the exchanger runs on a fixed steam pressure, the operator sees a lower condensate temperature or a higher condensate level, and the control valve opens further to compensate, which increases flow through the tubes and accelerates the fouling. The diagnostic question is always the same: has the coefficient fallen because of deposits, because the U-value was optimistic at design stage, or because the flow distribution has changed? A baseline measurement of the duty at commissioning makes this much easier to answer.

Fouling, Scaling and Their Different Behaviour

Fouling and scaling are often used interchangeably, but they behave differently. Fouling is the accumulation of suspended solids, biological growth, oil or polymer on the heat transfer surface. Scaling is the precipitation of dissolved salts when the surface temperature exceeds the saturation point of the scale-forming species. The commonest scales are calcium carbonate, calcium sulphate and calcium phosphate, and the driving condition is a wall temperature above the precipitation temperature of the scale. Since the wall temperature sits between the bulk fluid temperature and the hot-side temperature, hot-side service on the shell with a cold, hard-water stream on the tubes is a classic scaling configuration. In cooling water systems, biological growth and suspended solids dominate, and algae can also block tubes. Both produce the same effect: an insulating layer, a rise in pressure drop and a loss of effective area. The difference matters for the remedy, since organic deposits can often be removed by mechanical cleaning, while hard adherent scale usually needs an acid descaling treatment.

Identifying the Cause of a Performance Loss

When the duty drops, a structured approach avoids guesswork. Start with a temperature profile along the exchanger on both sides and look at the shape of the curve rather than only the end values. If the cold-side outlet temperature is depressed but the cold-side inlet is normal, a loss of area is more likely than a flow distribution problem. Next, compare the differential pressure against the design value. A large pressure drop rise on the tube side with only a moderate temperature change suggests a blockage or a partially plugged bundle, a shifted baffle set or a failed support plate. A temperature difference rise with a small pressure drop change points to surface fouling or an incorrect baseline U-value. Check the instruments first, because a drifted element or an uncalibrated flow meter will imitate a fouling problem. An ultrasonic or thermography survey of the shell reveals where deposits or blocked tubes are located, and a borescope or eddy current examination confirms wall thinning and blockage. In plate exchangers, the equivalent check is to open the unit and look at the plate surfaces.

Cleaning, Descaling and CIP Practice

Cleaning methods should match the deposit and the equipment. For shell-and-tube units, mechanical cleaning with brushes, plugs and water jets works well for loose solids and biofilm but is ineffective against hard scale. Chemical cleaning with an inhibited acid solution, circulated at elevated temperature, dissolves carbonate and sulphate scale, and the concentration, temperature and dwell time must be controlled so the base metal is not attacked. Inhibitors slow the dissolution of steel, and the chemistry should be checked against the metallurgy in use, particularly for stainless steel, titanium and aluminium-bronze materials. Spiral plate and many plate heat exchangers rely on the inherent scouring of the channel geometry plus periodic chemical cleaning. Air-cooled exchangers need the finned tube bundle cleaned with brushes, low-pressure water and, where the process allows, a cleaning fluid that does not attack the coating. A CIP system using detergent, caustic and acid stages is preferred in food, beverage and pharmaceutical service, and the whole circuit must be designed for full drainability. CIP cycles should be validated for concentration, temperature, time and rinse coverage.

Maintenance Schedule and Monitoring

A monitored heat exchanger rarely needs emergency work. The key parameters are the inlet and outlet temperature on both sides, the differential pressure on both sides, and the control valve position or the steam-to-feed ratio. Trending these against a stored commissioning baseline reveals fouling before the duty is missed. During inspection, check the tube surfaces, the baffles and support plates, the tube-to-tubesheet joints, the gasket condition in plate units, the sealing faces of floating heads, and the corrosion allowance consumed on the shell and channel. An ultrasonic thickness survey of the shell, nozzle reinforcement areas and channel covers is scheduled on a multi-year rotation, and the results compared against the design thickness to establish the remaining life. Instrument calibration belongs on the same schedule, because monitoring built on unverified instruments will misdirect the maintenance effort.

ParameterNormal behaviourWarning sign
Hot side outlet temperatureStable at design dutySlow rise across several days
Cold side outlet temperatureTracks set pointDrifts away from target
Pressure drop, tube sideConstant at design flowProgressive increase
Pressure drop, shell sideConstant at design flowStep change or noise
Effective U-valueClose to design basisBelow 80 percent of design
Condensate level and temperatureStable trap dischargeHigh temperature, low level

Energy Efficiency and Temperature Approach

Energy performance in a heat exchanger is governed by the temperature approach, the difference between the two outlet temperatures, or between the hot outlet and the cold outlet. A small approach means the exchanger works efficiently and the log-mean temperature difference is large for a given duty. As fouling develops, the approach widens, and more steam or hot utility is consumed for the same production. Air-cooled exchangers are limited by the approach between the process outlet and the dry bulb temperature, so they need more fan power and a generous surface area to recover the approach. Retrofitting a finned tube bundle, adding a second tube pass, or replacing a fouling-prone service with a spiral plate exchanger can all reduce utility consumption, and the calculation should be done on the annual utility cost rather than on the equipment price alone. Insulation on the shell and on the connecting piping is often overlooked, and a lagging survey usually recovers a large part of the loss. Insulation is also a safety consideration, because a hot bare surface is a burn hazard and a cold surface below the dew point will condensate and cause corrosion under the lagging. Variable speed drives on pumps and fans can trim energy use where the load varies through the year.

Plate Gasket Materials and Sealing Reliability

In a gasketed plate heat exchanger, the gasket is the sealing element, the pressure seal and the compliance member that allows the plate pack to expand under temperature cycling. Gaskets are normally elastomeric, commonly NBR, EPDM or FKM, and the choice is dictated by the medium and temperature. EPDM resists steam, hot water and glycol mixtures and is a common default, but is attacked by mineral oils and hydrocarbons. NBR handles oils and hydrocarbons well but has limited steam resistance at high temperature. FKM offers high temperature and chemical resistance but is expensive and can be attacked by amines and some ketones. PTFE and graphite gaskets are used at higher temperature and in aggressive chemical service. The gasket must also be compatible with the plate coating. Gasket failure typically presents as external leakage at the frame, a rapid pressure drop, or product contamination by the service fluid. Common causes include thermal ageing and compression set, over-tightening the frame bolts, a differential pressure above the gasket rating, a cold start with a full pressure step, and a misaligned plate pack. Gaskets should be replaced on every opening, and the specified torque sequence followed, because an unevenly compressed pack causes repeat leaks.

Common Failure Modes and Troubleshooting

Most field problems fall into a small number of patterns. A tube leak in a shell-and-tube unit is often caused by corrosion thinning, fretting at a support plate, erosion from high velocity carrying solids, or vibration fatigue, and is confirmed by the shell leak test or an eddy current survey. A flange or channel cover leak usually points to a damaged gasket, a distorted sealing face, bolt relaxation or a thermal expansion restraint, and the check is to confirm that the piping does not transmit load into the nozzle. Excessive vibration is dominated by shell-side cross-flow, and the remedies are a revised baffle cut, added tube support, restricted shell velocity or antivibration bars. A sudden loss of duty with no change in the flow is normally a control or measurement problem, an air lock on the shell side, or a blocked strainer upstream. Elevated shell-side outlet temperature with a high condensate temperature usually indicates a low steam trap or a flooded shell. Corrosion problems are diagnosed by locating the pattern: pitting at the tube-to-tubesheet crevice, thinning on the shell side of a condensing service, or attack on the tube side where velocity is highest. A structured sequence, from instrumentation to flow path to deposits to material, resolves most cases without dismantling.

Troubleshooting Workflow and Symptom Reference

A disciplined workflow starts with confirming the measurements, then comparing temperatures, pressure drops and valve positions with the commissioning baseline, then isolating whether the change is on one side or both, and only then deciding to open the equipment. Opening an exchanger is the slowest and most expensive diagnostic step, so it should follow the analytical checks. The table below summarises the symptom patterns behind most service complaints and the first action in each case.

SymptomLikely causeFirst action
Outlet temperature drifts upFouling or low flowCheck flow and pressure drop against baseline
Pressure drop rises sharplyBlocked tubes or strainerInspect strainer and bundle condition
External leak at frameGasket ageing or over-torqueCheck gasket, torque and alignment
Shell-side noiseCross-flow vibrationReview baffle cut and tube support
Wide approach, no pressure changeSurface foulingDescale and review U-value
Product contaminationGasket or seal intrusionReplace gasket, verify seal material

Frequently Asked Questions

How often should a heat exchanger be cleaned?

The interval depends on the fouling rate of the service, not on a fixed calendar rule. A clean-water service may need an annual inspection, while seawater or raw process streams can require cleaning every few months. The reliable approach is to trigger cleaning on measured performance, using the effective U-value and the pressure drop against the commissioning baseline.

Can a fouled heat exchanger be cleaned without opening it?

Often yes. Chemical descaling can be circulated through the unit without dismantling, provided the exchanger is arranged for it, the deposit is scale, and the base metal and gaskets tolerate the chemistry. Organic fouling normally needs mechanical access, meaning withdrawal of a removable bundle or opening a plate unit.

Why does the pressure drop increase before the duty falls?

Deposits first narrow the flow path, raising friction loss, while the thermal resistance builds more gradually. As the layer thickens, the heat transfer coefficient falls and the outlet temperature moves away from the design value. Monitoring the pressure differential therefore gives earlier warning than temperature alone.

Is a rising condensate temperature a fouling problem?

Not always. A rising condensate temperature with a low level points to a failed or leaking steam trap, which lets live steam blow through and floods the shell. If the condensate level is normal and the shell-side approach has widened, fouling is the likelier cause.

44 次

相关文档

Copy right © 2019 Wuxi Chemical Equipment Co., Ltd. All Rights Reserved Website Design: Wuxi Wangke